Franchised

GRP Manhole Covers

Nominal Diameters from 150 – 3600 mm Products- Standard Manholes – Tangential Manholes – Customized Manholes – Inspection Entrance – Well Chambers, Pump Shafts, Sewer Overflows, etc. – Accessories: Ladder, Fittings, Covers etc. Features:

  • Anti-Corrosive
  • Zero Scrap Value
  • High Strength to Weight Ratio
  • Light weight hence ease of handling
  • Long Service Life
  • Easy Installation
  • Fire Retardant
  • Can be designed to take the loads from 2.5tons to 40tons
  • Any color options(RAL shades)

GRP Storage Tanks

Features: —Light weight, the density of FRP is 1.5-1.9g/cm3 is quarter of steel, but its strength is higher.
—Corrosion resistant, we can select the different kinds of resin against the variety of the media, such as acid, alkali, salt, oil and solvent. Can be used in the every aspects for corrosion resistance, and can be replaced the stainless steel, nonferrous metal and other kind of material.
—High strength, we can meet the demand of corresponding temperature and pressure by changing the type of resin and fiberglass of structural layer, adjusting lamination.

The inner surface is smooth, the roughness coefficient is 0.0084, has good sanitary property, it is easier to clean as clear, can resist the corrosion of animalcule. If the foods staff grade resin used in the inner liner, the product can meet the requirement of sanitation without toxicity and taste.
—Good property against low temperature, it can be used in the condition of negative 80℃, it is suitable for cool area.
—Thermal expansion factor is 2×10-5℃,thermal conductivity is 0.2kcal.m/㎡.h.℃,good thermal insulation property.
—The formation is easy, maintenance is convenient and it is suitable for the comprehensive equipment. The maxi vessel can be wound at the site.
—Can be matched with the accessories, such as the level indicator, handrail, ladder, platform and others.

Applications:

  • Chemical vessels,
  • Heat insulation tank,
  • Agitator kettle,
  • Fermentation tank and separator etc.
  • Pharmaceutical and water treatment etc.

GRP Pipes

The GRP (Glass Re pipes are manufactured by thermoset resins and glass fiber reinforcements and the pipes are designed to prevent corrosion and increase the product life cycle. Because of the lightweight material of GRP product, there are reduced installation costs and the smoother bore of GRP material equates to improved flow efficiency. The glass fiber pipes has a reduces paraffin and scale build-up, leading to lower maintenance costs over time.

Benefits:

  • High corrosion resistance
  • High abrasion resistance
  • Low weight
  • UV resistance
  • High structural load capacity
  • Low operating and maintenance costs
  • Variable lengths
  • High stiffness classes available
  • Installation possible irrespective of weather conditions
  • Consistent high quality
  • More Service life
  • Leak-tight system for maximum loss-free flow
  • Very smooth inner pipe surfaces minimize friction and pressure loss and simplify hygienic measures

GRP Sheets

  • Fiberglass reinforce panels provide a strong scratch resistant surface.
  • GRP could be cleaned easily using regular detergents, high pressure washers, or even by using steam.
  • Glass Fiber reinforced panel is a lightweight panel that is easy to install
  • GRP could be installed either with glue or fasteners
  • Maximum sanitation protection
  • Improved chemical resistance
  • FRP could be installed over any existing wall surface, by following some simple steps and no high tech tools are required.
  • High impact resistance from shattering and scratches
  • Superior flexibility
  • FRP could save you money when preferred over other building materials
  • Fiberglass reinforced panels will allow the growth of mold or mildew and will not rust or corrode

GRP Electrical SMC Products

GRP is a non conductive and processes high dielectric strength, and enables light weight solutions for the electrical applications. IM deals with the following GRP Products for the electrical industry application:

  • Cross Arms
  • Epoxy Castings & Insulators
  • Epoxy Rods
  • Electric Boxes
  • Electric Motor Covers
  • Trefoil Clamps

For the benefits of GRP products

GRP Light Utility Poles

Fiberglass power transmission pole has a higher strength-to-weight ratio than steel, wood or concrete and weighs substantially less. Approximately 30% the weight of wood, 60% of steel and 15% or less of concrete. Utilities specify and install our composite utility poles for their inherent properties including:

  • Light Weight
  • Corrosion and Rot Resistance
  • Superior Dielectric Strength
  • Unaffected by Woodpeckers and Termites
  • Environmentally Safe, Will Not Leach
  • No Pesticides or Preservatives
  • Lineman Safety
  • Community Safety
  • High Reliability
  • Advanced UV protection

Pole Ordering System

Pole Type Pole Length(m) Resin Pole Color
RP-ROUNDPOLE 7 VINYL Light Grey
OP-OCTOGANAL POLE 9 ISO-POLY Brown
12 Brown Grey
15
20
Etc.

Comparison: Composite Poles Vs Metal Swaged Poles:

Features FRP Metal
Weight Light Heavy(3 times heavier than FRP pipes)
Corrosion Non corrosive Highly corrosive
Maintenance Maintenance free Ongoing maintenance required
Installation cost Low High
Transportation Cost Low High
Periodic Painting Not required Required
Construction Joint less Multiple joints
Relocation Easy & hand carried Not feasible
Current Leakage Shock proof, Electrically non conductive Conductive, Prone to current leakage & shock

 

GRP Fencing line & corner posts, garden benches cross posts are to be manufactured by the pultrusion process with a glass content minimum of 45%, maximum of 55% by weight. The structural shapes shall be composed of fiberglass reinforcement and resin in qualities, quantities, properties, arrangements and dimensions as necessary to meet the application requirements. Benefits:

  • Ease of Assembly
  • Low Maintenance
  • Cost Effective
  • Light weight components
  • Low freight costs
  • Internal Connection System
  • UV Resistant
  • Fire Retardant

GRP Deck Panels

GRP Fencing line & corner posts, garden benches cross posts are to be manufactured by the pultrusion process with a glass content minimum of 45%, maximum of 55% by weight. The structural shapes shall be composed of fiberglass reinforcement and resin in qualities, quantities, properties, arrangements and dimensions as necessary to meet the application requirements. Benefits:

  • Ease of Assembly
  • Low Maintenance
  • Cost Effective
  • Light weight components
  • Low freight costs
  • Internal Connection System
  • UV Resistant
  • Fire Retardant